Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes
  • Show More Model Years
  • Show Fewer Model Years

Parts & Accessories

$55.00
- E*thirteen freehub bodies feature 6 degree (60 Point) engagement - Kits include freehub body, bearings, springs, and pawls - SRAM XD-11 Freehub body converts all e*thirteen plus level hubs for use with SRAM XD-11 drivetrains
$13.00
We designed Teravail tubeless tape for no-hassle installation. Its slight stretch allows the tape to easily conform to your rims. The translucent material shows you exactly where the tape makes contact. It's tacky enough to prevent shifting but easy to pull up if needed, and it won't leave residue on your rims. - Teravail Tubeless Tape comes in a variety of widths to fit almost any rim. - Teravail Tubeless Tape is available in a variety of widths and roll lengths. - Ten-meter length is enough for a single layer on approximately four wheels
$3.00
- Shell: 8mm flanged axle nut - Flanged
$12.00
- Replacement rear skewer - Spacing: 135mm - Material: Steel
$21.00
- M-Pulse front axles incorporate drive-side end cap and rear axles the non-drive side end cap - Neo OS axles are steel and compatible with standard Neo hubs for riders looking for a steel option - Instructions and hub axle determinations are available
$24.00
Stan's lightweight aluminum valve stems are half the weight of Stan's standard brass valves. The secure round base is compatible with most tubeless rims and a perfect fit for all Stan's BST rims. A removable valve core makes adding sealant easy, and these babies fit up to 8mm valve hole. Sold as a pair.
$22.00
Front end cap conversion kits for NoTubes Neo and Neo Ultimate - SealLock end caps feature a low friction U-cup seal that snaps into place
$20.00
Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.
$16.00 - $20.00
SRAM's X0 conversion caps are the ticket for converting your X0 hubs to a different axle type.
$52.00
After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer the highest quality, simple, lightweight alternative to that bulky handle. - This axle is compatible with bikes that have a Focus R.A.T. thru-axle in the fork with 100 x 12mm front hubs. - The axle is precision CNC-machined in the USA from 7075 aluminum and hard-anodized for rugged durability. Our axles are built to the tightest standards in the industry. - No special tools required. Design allows for wheel installation and removal using your standard 6mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.
$65.00
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
$8.95 - $9.00
Lightweight and easy to install, there are Ritchey rim strips for all wheel sizes and types. - Easily snaps over your rims - Stretchy, tightly woven material provides a close fit and protects from abrasion - Sold as a pair - Not for tubeless set up
$6.00
Origin-8's Pro Pulsion Rim Strips are made from a super-durable, environmentally friendly PVC material.
$16.00 - $18.00
The Muc-Off Tubeless Rim tape is made from their proprietary performance material with a pressure-sensitive adhesive to provide just the right amount stretch whilst maintaining durability and strength needed to create a lasting airtight seal. Semi-transparent material makes locating the valve hole easy.
$32.00
V2 Tubeless valves are stronger, lighter, and even easier to use thanks to the machined aircraft grade 7075 aluminum and Muc-Off's new Tire Insert air ?ow system. The new design features six slots that are machined into the base of the valve stem, allows tubeless sealant ?uid and air to ?ow freely, even when running tubeless tire inserts. - 7075 Machined Aluminum valve stem and cap - Tire Insert air flow system keep air moving freely and compatible with most tire foam inserts - 4mm machined Allen Key slot for easy installation and removal - Includes Valve Core Removal Tool (integrated into spare alloy cap) - Supplied with various rubber bases to optimize fit with multiple rim types
$8.00
Grade 10 chromium steel balls MR17287LLB - 17 x 28 x 7mm 6808LLB - 30 x 42 x 7mm
$7.00 - $12.00
- MAX bearings are filled completely with high precision Grade 10 balls for maximum load capacity - No retainer means these bearings have 40 percent more capacity
$48.00
Front axle conversion kits convert your hub to fit a new axle measurement or for a new group set.
$48.00
Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.
$38.00 $39.00 3% Off
When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows you to fully tighten the axle and perfectly position the lever. - Ratcheting system tightens skewers with turns rather than a cam - Lever can be rotated into an ideal position after tightening - Conical X12 washer, compatible with Syntace X-12 system - Thread Pitch: 12 x 1.0mm
$150.00
CushCore is an engineered foam insert to be mounted inside a tire, designed to absorb impacts, reduce vibration, and increase lateral stability. These characteristics translate to a more controlled, comfortable, and faster ride. - The system is designed to be used with tubeless-ready or tubeless converted rims and tires and is compatible with tubeless tire sealants - A specially designed tubeless air valve is included with each insert; allowing air to move through the valve without becoming obstructed by the insert - The insert divides the inner volume of the tire in half, maintaining air underneath the tread and the foam insert next to the rim - Fits tire widths 2.1 – 2.6" and rims with internal width 22 – 35mm Includes: - 2 CushCore Inserts - 2 CushCore Tubeless Air Valves - 4 Rim Stickers - Installation Instructions
Page 1 of 1